|
I am using my laser in my garage in SC "Its hot" I have
|
|
6
|
68
|
September 19, 2016
|
|
MoshiDraw Manual and Software David Pasick You do not have comments enabled on your
|
|
0
|
81
|
September 19, 2016
|
|
Hi everyone im in the uk just purchased a k40 laser it worked fine
|
|
20
|
243
|
September 19, 2016
|
|
Im hoping someone can help as l am close to taking a hammer to
|
|
11
|
64
|
September 19, 2016
|
|
Can anyone tecommend an aliexpress seller?
|
|
5
|
64
|
September 19, 2016
|
|
Hey guys im kinda new to this but so excuse me if this is
|
|
5
|
321
|
September 19, 2016
|
|
A couple of quick jobs to test out the machine after upgrading to my
|
|
14
|
133
|
September 19, 2016
|
|
Completed the K40-S DC power and distribution module wiring and base that I showed
|
|
0
|
112
|
September 19, 2016
|
|
My first living hinge.
|
|
7
|
279
|
September 18, 2016
|
|
After a lot of being messed about with the seller of my dangerous machine
|
|
0
|
64
|
September 18, 2016
|
|
Here is a laser engraving i did on my k40 on 9mm mdf,
|
|
0
|
112
|
September 18, 2016
|
|
Can anyone tell me how to get coreldraw x8 to work with my k40
|
|
8
|
78
|
September 18, 2016
|
|
I am finally back home and again working on my smoothies conversion.
|
|
8
|
113
|
September 18, 2016
|
|
I have a K40 laser, which stopped burning half way through a job.
|
|
4
|
66
|
September 18, 2016
|
|
Question.. I could use some help please.
|
|
7
|
99
|
September 18, 2016
|
|
Google+ post by Ariel Yahni (UniKpty) on 2016-09-17 03:47:19 UTC
|
|
5
|
76
|
September 18, 2016
|
|
Now what. Why is the hole cuts not lined up near the bottom,
|
|
12
|
113
|
September 18, 2016
|
|
As a comparison for the terrain scraper,
|
|
4
|
128
|
September 17, 2016
|
|
Can anyone send me a link where to download CoralLaser,
|
|
3
|
108
|
September 17, 2016
|
|
Just got a older never used k40 .I've done all the setup ,The disk
|
|
0
|
69
|
September 17, 2016
|
|
The Redsail LE400 conversion is almost complete.
|
|
2
|
111
|
September 17, 2016
|
|
So glad I switched to a smoothieboard.
|
|
7
|
105
|
September 17, 2016
|
|
I just got my K40 last week.
|
|
5
|
509
|
September 17, 2016
|
|
Anyone had a Water Error 1 on the red laser.
|
|
3
|
81
|
September 17, 2016
|
|
Any recommendation on a replacement water pump?
|
|
1
|
72
|
September 17, 2016
|
|
Last week it was raining here and went down to the basement to check
|
|
2
|
57
|
September 17, 2016
|
|
Completed my K40S interface board connects to all control signals,
|
|
4
|
104
|
September 17, 2016
|
|
i seem to have lost the stock zero point when i turn I the
|
|
13
|
88
|
September 16, 2016
|
|
Hi all. I finished my new Laser exhaust ducting setup,
|
|
5
|
211
|
September 16, 2016
|
|
What started out as a MakeCNC purchased plan, has been heavily modified to this.
|
|
12
|
85
|
September 16, 2016
|