|
last question for tonight...how many links in the cable chain does it take to
|
|
0
|
104
|
December 3, 2017
|
|
Really hate to ask as I know it's an easy thing to do,
|
|
6
|
218
|
November 30, 2017
|
|
And now that she is pretty much done, here is a Marvin at 500%.
|
|
4
|
201
|
November 28, 2017
|
|
Anyone found an alternative for the a_7z41mpsb08m from SDP/SI?
|
|
8
|
171
|
November 28, 2017
|
|
I have a a few questions (OK, 6) about the BOM,
|
|
2
|
160
|
November 28, 2017
|
|
Opinion on going the linear rod route or linear guide rails.
|
|
5
|
92
|
November 28, 2017
|
|
Hi all, really generic question.
|
|
5
|
137
|
November 27, 2017
|
|
Greetings all- I have been lurking and browsing for a bit trying to absorb
|
|
4
|
81
|
November 24, 2017
|
|
I am one of those with a half built printer that is begging to
|
|
13
|
201
|
November 24, 2017
|
|
Hi guys, May I ask you a service;
|
|
5
|
96
|
November 22, 2017
|
|
Alright, this has really stumped me...
|
|
0
|
105
|
November 21, 2017
|
|
Hi all, I'm back live and kicking.
|
|
5
|
95
|
November 21, 2017
|
|
Had a print fail on me this weekend due to my Bowden tube between
|
|
22
|
271
|
November 19, 2017
|
|
Looking to use just a rectangular build plate like Walter's,
|
|
4
|
92
|
November 15, 2017
|
|
The Hybrid. Always had bad z wobble with the increased height,
|
|
1
|
156
|
November 14, 2017
|
|
So I'm finally at a point where I have a working derivative/custom Eust.
|
|
7
|
227
|
November 12, 2017
|
|
Is there some particular reason the to use the Azteeg X5 GT over the
|
|
7
|
200
|
November 8, 2017
|
|
Had anyone tried out a remote direct drive extruder such as the Flex3Drive or
|
|
5
|
99
|
October 29, 2017
|
|
Not the most pleasant surprise powering on my Azteeg X5 GT :( I followed
|
|
10
|
191
|
October 27, 2017
|
|
I'm ordering up my parts for my build and I'm stuck deciding between 8mm
|
|
5
|
198
|
October 26, 2017
|
|
Eric Lien I recently started using Simplify3d (it's about time,
|
|
73
|
346
|
October 13, 2017
|
|
As a PSA, I had a weird issue with my x.y axis surging.
|
|
3
|
65
|
October 11, 2017
|
|
I'm getting this noise only when moving in Y at low speeds.
|
|
8
|
116
|
October 4, 2017
|
|
Anyone know if I can use the smoothie config posted on the guthub for
|
|
2
|
76
|
September 10, 2017
|
|
Anyone have a good source for IGUS ECLM 08 bearings?
|
|
1
|
83
|
September 9, 2017
|
|
About to give up on Bowden, running 2 Saitflint's with hobb goblin drive gears.
|
|
3
|
130
|
September 6, 2017
|
|
Really simple question regarding mosfet driver module for PWM control of cooling fans that
|
|
4
|
128
|
September 4, 2017
|
|
Does anyone here have a working config file and the latest firmware for the
|
|
3
|
69
|
September 2, 2017
|
|
I'm literally only a week into owning a printer at all,
|
|
14
|
141
|
August 5, 2017
|
|
Hello, I'm back! Currently running the Azteeg X3,
|
|
3
|
113
|
August 5, 2017
|